- 您现在的位置：买卖IC网 > Sheet目录342 > MC56F8006DEMO-T (Freescale Semiconductor)BOARD DEMO FOR MC56F8006 DSP
Chapter 2
Technical Summary
2.1 Options
2.1.1 JP1: IRQ_SW1 Input Select
JP1 is a cutaway type option on the bottom side of the DEMO board. Default connection is to
MC56F8006 I/O port B2. Optional connection to port B4 is provided for user application.
2.1.2 JP2: IRQ_SW2 Input Select
JP2 is a cutaway type option on the bottom side of the DEMO board. Default connection is to
MC56F8006 I/O port B3. Optional connection to port B5 is provided for user application.
2.1.3 JP3: +3.3 V Enable
JP3 option installed (default) provides +3.3V regulated voltage from the onboard VR1 voltage
regulator to power the DEMO board. Open this option to power the board from an external +3.3V
source or from the J1 connector.
2.1.4 JP4: +Vopt Enable
JP4 option installed provides a connection from J1 pin 1 to the board +3.3V power connection.
This option is open/idle by default. This option may be applied to provide board +3.3 V regulated
voltage to the J1 connector (JP3 installed also) or to source +3.3V from J1 (JP3 open) to power
the board from a connected host platform.
2.1.5 TX_EN and RX_EN Option Jumpers
TX_EN and RX_EN options provide selection of the serial port connection for the MC56F8006 SCI
serial port. MC56F8006 ports B6 (RXD) and B7 (TXD) provide the SCI I/O pins for these options.
Default option setting is for the USB port to support the SCI serial port. The RS-232 serial port is
not populated by default but may be applied by the user if populated.
TX_EN and RX_EN = position 1–2 default, USB BDM serial port support.
Position 2–3 = RS-232 port.
See the support DVD for virtual terminal software to support the USB serial port.
2.2 User Components
2.2.1 LED1: 6 Indicators
Six indicator LEDs are provided for user application indications. The LEDs are applied to the
MC56F8006 I/O port A0/PWM0 to A5/PWM5 signals. Buffers are applied so that the LEDs will not
load the I/O port pins during operation. LEDs are on during the applied signals logic high level.
The following table provides the signal and LED reference.
LED
LED1
LED2
LED3
LED4
LED5
LED6
6
MC56F8006 I/O Port
PAO/PWM0
PA1/PWM1
PA2/PWM2
PA3/PWM3
PA4/PWM4
PA5/PWM5
LED Color
RED
RED
GREEN
GREEN
YELLOW
YELLOW
www.freescale.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MCB1114
BOARD EVALUATION FOR NXP LPC1114
MCB11C14
BOARD EVAL FOR NXP LPC11C14
MCB2470
BOARD EVAL NXP LPC247X SERIES
MCBSTM32EXL
BOARD EVALUATION FOR STM32F103ZE
MCBTMPM330
BOARD EVAL TOSHIBA TMPM330 SER
MCIMX25WPDKJ
KIT DEVELOPMENT WINCE IMX25
MCIMX53-START-R
KIT DEVELOPMENT I.MX53
MCM69C432TQ20
IC CAM 1MB 50MHZ 100LQFP
相关代理商/技术参数
MC56F8006DEMO-T
制造商:Freescale Semiconductor 功能描述:MC56F8006DEMO board including USB TAP
MC56F8006DEMO-T-PROMO
制造商:Freescale Semiconductor 功能描述:KIT DEMO MC56F8006 DSC BOARD
MC56F8006MLC
制造商:Freescale Semiconductor 功能描述:DSC 32LQFP 16K FLASH - Bulk
MC56F8006VBM
功能描述:数字信号处理器和控制器 - DSP, DSC DSC 32SDIP 16K Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MC56F8006VLC
功能描述:数字信号处理器和控制器 - DSP, DSC DSC 32LQFP 16K Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MC56F8006VLF
功能描述:数字信号处理器和控制器 - DSP, DSC DSC 48LQFP 16K Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
MC56F8006VLF
制造商:Freescale Semiconductor 功能描述:IC DSC 16BIT 16KB 32MHZ 3.6V LQFP-48
MC56F8006VWL
功能描述:数字信号处理器和控制器 - DSP, DSC 16 BIT DSPHC RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT